Carlo Gavazzi Controls

Approx. 1,800 / Piece Get Latest Price

Product Brochure
3-Phase relay for detection of incorrect phase sequence, total and partial phase loss. Supply range from 208 to 480 VAC. For mounting on DIN rail. Housing 17.5 mm wide, SPDT relay output, suitable for back and front panel mounting. The device detects regenerated voltage up to 85% of the nominal voltage (phase-phase).

Features:

• 3-phase monitoring relay for phase sequence and phase loss
• Detects when all phases are present and have the correct sequence
• Measures its own power supply
• Power supply range: 208 to 480 VAC (±15%)
• Output: 5 A SPDT relay normally energized
• For mounting on DIN-rail in accordance with DIN/EN 50 022
• 17.5 mm DIN-rail housing (DIN 43880) 
• LED indication for relay and power supply ON.

Approx. 1,800 / Piece Get Latest Price

Product Brochure
DTA02C115 precise thermistor monitoring relays. They can be used to monitor the temperature of the coils of a motor with built-in PTC’s. The alarm status of the relay can be reset by either an external contact or an internal button (DTA02, PTA02). The test button allows the simulation of the fault condition (DTA02, PTA02). The red LED indicates the alarm status.

Features:

• Motor temperature monitoring relay
• Measuring ranges: PTC according to EN 44081 
• Remote and local alarm reset (DTA02, PTA02)
• Output: 8 A SPDT (PTA01/DTA01/DTA02) or SPST (DTA01) relay, normally energized 
• For mounting on DIN-rail in accordance with DIN/EN 50 022 (DTA01, DTA02) or plug-in module (PTA01, PTA02)
• 22.5 mm Euronorm housing (DTA01, DTA02) or 36 mm plug-in module (PTA01, PTA02)
• LED indication for relay and power supply ON (DTA02, PTA02)
• Galvanically separated power supply.

Approx. 11,500 / Number Get Latest Price

Product Brochure

Three-phase energy meter with removable front LCD display unit. The same unit can be used either as a DIN-rail mounting or a panel mounting energy meter. This general purpose three-phase energy meter is suitable for both active and reactive energy metering for cost allocation but also for main electrical parameter measurement and retransmission (transducer function). Housing for DIN-rail mounting with IP50 (front) protection degree. Current measurements carried out by means of external current transformers and voltage measurements carried out either by means of direct connection or by means of potential transformers. EM21- 72D is provided, as standard, with a pulsating output for active energy retransmission. In addition a 2-wire RS485 communication port is available as an option.

Approx. 24,500 / Piece Get Latest Price

Features:

• Virtual measuring device (sum of two 3-phase or six 1-phase loads)
• Electricity meter with 6 + 1 DGT reading
• Current measurement up to 32 A using an external TCD06B current transformer block
• Immediate reading of variables: 3-DGT (power: 3-DGT, current and voltage: 3-DGT)
• Single phase variables: V, A, kW
• Total energy measurements: kWh and kvarh total
• TRMS measurements of distorted sine waves (voltages / currents)
• Internal power Supplies
• RS485 serial communication port (standard).

Approx. 970 / Piece Get Latest Price

Product Brochure

This family of 2-Phase Motor Reversing Controller is designed to switch 3-phase motors rated up to 5.5 kW. The built-in interlocking circuitry prevents the relay from switching both directions at the same time. A dual colour LED indicates direction "forward" when green and direction "reverse" when red. The output is protected from excessive voltage fluctuations (transients) by built-in varistors. Furthermore, optimum reliability is achieved by soldering the output thyristor chips directly on to the ceramic substrate (Direct Copper Bonding). The housing is designed to incorporate a temperature limit switch. It is recommended to install an appropriate semiconductor fuse in series with the relay.

Features:

• Motor reversing for 3-phase induction motors up to 5.5 kW
• Rated operational voltage: Up to 480 VACrms
• Built-in interlock function
• DC or AC control voltage
• Built-in voltage transient protection
• LED indication for direction
• Isolation: Optocoupler (input-output) 4000 VACrms
• Direct copper bonding technology

Approx. 4,650 / Piece Get Latest Price

We are an eminent entity engaged in offering an extensive range of quality assured DC Energy Meter. Owing to features like durability and easy installation, the offered meter is extensively used DC devices. A team of our vendor’s adept professionals, with hard-earned experience manufacture the offered meter using high grade raw material. The offered meter is available with us in various sizes, designs and other related specifications.

Features:

• Measurements: 2 temperatures, 1 analogue input, 1 pulse rate input
• Two temperature inputs: Pt100-Pt1000 type
• One 120mV or 20mA analogue input with scaling capability
• One pulse rate input for general speed/flow measurements
• Auxiliary communication bus to VMU-C unit or VMU-M unit depending on which bus it belongs to
• Auxiliary power supply from VMU-C or VMU-M unit depending on which bus it belongs to
• Dimensions: 1-DIN module
• Protection degree (front): IP40

Description:

• Measurements: 2 temperatures, 1 analogue input, 1 pulse rate input
• Two temperature inputs: Pt100-Pt1000 type
• One 120mV or 20mA analogue input with scaling capability
• One pulse rate input for general speed/flow measurements
• Auxiliary communication bus to VMU-C unit or VMU-M unit depending on which bus it belongs to
• Auxiliary power supply from VMU-C or VMU-M unit depending on which bus it belongs to
• Dimensions: 1-DIN module
• Protection degree (front): IP40

Approx. 2,592 / Number Get Latest Price

Product Brochure
Multi-voltage timer with 7 knob-selectable functions and 7 knob-selectable time ranges within 0.1s and 100h. For mounting on DIN-rail. Housing 17.5 mm wide for SPDT version and 35.5 mm for DPDT version, suitable both for back and front panel mounting.

Features:

• Automatic or manual start
• Repeatability: ≤ 0.2%
• Output: 5 A SPDT or 5 A DPDT relays
• For mounting on DIN-rail in accordance with DIN/EN 50 022
• 17.5 mm (DMB51C) or 35.5 mm (DMB71D) DIN-rail housing (DIN 43880)
• Combined AC and DC power supply
• LED indication for relay status and power supply ON

Approx. 8,050 / Piece Get Latest Price

Product Brochure
Emergency Stop and Safety Gate modules according to EN 60204-1, EN 292-1/-2, EN 418 and EN1088. This family of safety module in Safety Category 4, includes fixed screw and detachable screw as well as automatic/manual or monitored manual restart versions.

Features:

• Safety Category 4 according to EN 954-1
• Category 0 Emergency Stop (EN 60204-1)
• 2 x 6 A NO safety outputs (NES02D)
• 3 x 6 A NO safety outputs and 1 x 6 A NC auxiliary output (NES13D)
• Automatic / manual or monitored manual reset
• Single / double channel operations
• LED indication for outputs status and power supply ON
• Connection by fixed or detachable terminals
• For mounting on DIN-rail in accordance with DIN/EN
• 22.5 mm Euronorm housing

Approx. 4,100 / Piece Get Latest Price

Product Brochure
Three-phase energy meter with built-in configuration joystick and LCD data displaying; particularly indicated for active and reactive energy metering and for cost allocation. Housing for DIN-rail mounting with IP50 (front) protection degree. Direct connection up to 65A. Moreover the meter is provided with either one pulsating output proportional to the active energy being measured or a serial communication port.

Features:

• Certified according to MID Directive (option PF only): †see “how to order” below
• Other version available (not certified, option X): see “how to order” on the next page
• Class 1 (kWh) according to EN62053-21 
• Class B (kWh) according to EN50470-3 
• Class 2 (kvarh) according to EN62053-23 
• Accuracy ±0.5 RDG (current/voltage) 
• Energy meter
• Instantaneous variables readout: 3 DGT 
• Energies readout: 7 DGT
• System variables: W, var, Phase-sequence.
• Single phase variables: A
• Energy measurements: total kWh and kvarh
• TRMS measurements of distorted sine waves (voltages/currents)
• Self power supply
• 1 pulsating output (optional)
• RS485 serial communication port (MODBUS-RTU) optional
• Dimensions: 4-DIN modules
• Protection degree (front): IP50
• Easy connections management

Approx. 5,680 / Number Get Latest Price

Product Brochure
Three-phase smart power analyzer with built-in advanced configuration system and LCD data displaying. Particularly recommended for the measurement of the main electrical variables. WM30 is based on a modular housing for panel mounting with IP65 (front) protection degree. Moreover, the analyzer can be provided with digital outputs that can be either for pulse proportional to the active and reactive energy being measured or/and for alarm outputs. The instrument can be equipped with the following modules: RS485/RS232, Ethernet, BACnet-IP or BACnet MS/TP communication ports, pulse and alarm outputs. Parameters programming and data reading can be easily performed by means of WM3040 Soft.

Features:

• One RS232 and RS485 port (on request)
• Communication protocol: MODBUS-RTU 
• MODBUS TCP/IP Ethernet port (on request)
• BACnet-IP over Ethernet port (on request)
• BACnet MS/TP over RS485, BTL approved (on request)
• Ethernet/IP port, ODVA approved (on request)
• Up to 2 digital outputs (pulse, alarm, remote control) (on request)
• Up to 4 freely configurable virtual alarms
• Up to 2 analogue outputs (+20mA, +10VDC) (on request)
• Class 0.5 (kWh) according to EN62053-22
• Class C (kWh) according to EN50470-3 
• Class 2 (kvarh) according to EN62053-23
• Accuracy ±0.2% RDG (current/voltage) 
• Instantaneous variables readout: 4x4 DGT
• Energies readout: 9+1 DGT
• System variables: VLL, VLN, A, VA, W, var, PF, Hz, Phase-sequence-asymmetry-loss.
• Single phase variables: VLL, VLN, AL, An (calculated), VA, W, var, PF
• Both system and single phase variables with average and max calculation
• Harmonic analysis (FFT) up to the 32nd harmonic (current and voltage)
• Energy measurements (imported/exported): total and partial kWh and kvarh
• Energy measurements according to ANSI C12.20 CA 0.5, ANSI C12.1 (revenue grade)
• Run hours counter (8+2 DGT)
• Real time clock function
• Application adaptable display and programming procedure (Easyprog function).

Approx. 60,000 / Piece Get Latest Price

Product Brochure
Three-phase power analyzer with built-in configuration keypad; Particularly indicated for the analysis of main, secondary and energy metering electrical variables. Housing for DIN-rail or wallmounting, IP40 (front) protection degree. Completely sealable housing. In case of direct connection up to 100A, the measuring input terminals are suitable for cables with a cross-section area from 6 to 35 mm2 . The special design of the instrument’s housing allows to add at any time the interface modules, even when the instrument is already installed.

The following modules are available:

• for all versions: pulses output; 
• only for the versions with auxiliary power supply: analogue output, RS485 port, alarm output or BUS Dupline.

Features:

• Front dimensions: 9 DIN modules 
• Analogue output by means of optional module (20mA or 10VDC)
• RS 422/485 Serial port by means of optional module
• Alarm output by means of optional module
• Dual pulse output by means of optional module
• Control of phase asymmetry
• Class 0.5 (current/voltage)
• Three-phase power analyzer
• Back-lighted LCD
• 4 x 31/2 DGT instantaneous variables read out
• 71/2 DGT energy read-out
• Measurements of system and phase variables: W, Wdmd, var, VA, VAdmd, PF (cos¿¿), V, A, Hz, THD-A, THD-V
• Measurements of total energies: kWh, kvarh
• Measurements of partial energies: kWh, kvarh
• Energy measurements according to EN61036 and EN61268
• TRMS measurements of distorted wave forms (voltages/currents)
• Two basic models: direct connection 20(100)AAC, CT 5(10)AAC and VT connection
• Maximum value indication of W dmd and VA dmd (only 5A version); maximum value indication of A (only 100A version).

Approx. 70,000 / Piece Get Latest Price

With Dupline, Carlo Gavazzi offers a complete bus solution, which is ready-to-use for small as well as medium-sized and large elevator companies. Dupline can be easily applied in all phases of a project and does not require PC’s or other advanced equipment, which most elevator installers are not trained to use.

Main features:

• User-friendly, noise immune and cost-effective
• Reduced installation and commissioning time
• The Master Module interfaces Dupline® to any Elevator Controller with a RS232 or RS485 port.Dupline Elevator Controller

Applications:

• Carlo Gavazzi's Dupline® 3-wire bus makes elevator control systems simpler and more effective than traditional systems. Space and cost saving I/O-boards with 2 inputs and outputs are mounted in each floor fixture and connected to the push button and lamps. In the elevator car, where the number of signals is higher, boards with multiple I/Os are used. All the I/O-boards are connected to the same wire cable, which provides both 24VDC power for lamps and floor indicators and serial communication connection with the Dupline® Master Module.

Approx. 1,500 / Piece Get Latest Price

Carlo Gavazzi is a leader in HVAC market, wide variety of products for the HVAC sector. HVAC (heating ventilation and air conditioning) products from carlogavazzi are ssr, sensor, smps, softstarters etc.

Features:

• AC semiconductor contactor
• MODBUS RTU interface over RS485
• RJ45 sockets for easy installation
• Dual sockets for daisy chaining
• Multi-function – 4 selectable modes of operation: ON/OFF, Phase angle, Distributed full cycle, Burst firing

Approx. 80,000 / Piece Get Latest Price

Carlo Gavazzi Energy Management systems provide information so that operators can identify consumption trends and take corrective actions. Analysing the power profile operators can also aggregate loads and so negotiate more favorable terms with the utility company. Real-time power consumption monitoring also allows a site manager to anticipate overload conditions that would, for example, trip a circuit breaker. Alarm thresholds can be set to warn managers if preset limits are reached. Carlo Gavazzi Energy Management equipment meets the requirements of commercial buildings, Industry and production facilities, services and infrastructures.

Features:

• Wide range of power quality meters, energy meters, and transducers
• Fast installation, programming and display information reading
• Easy communications with PLC or PC control systems to provide plant-wide monitoring

Approx. 4,900 / Piece Get Latest Price

Carlo Gavazzi's energy management products provide information to identify consumption trends and take corrective actions. Real time power consumption monitoring also allows a site manager to anticipate overload conditions, exploiting alarm thresholds. Energy management equipment meets the requirements of commercial buildings, industry and production facilities, services and infrastructures. In addition, fiscal metering is possible in Europe thanks to MID certification

Approx. 20,615 / Piece Get Latest Price

Class B (kWh) according to EN50470-3 ??? Class 1 (kWh) according to EN62053-21 ???Class 2 (kvarh) according to EN62053-23 ??? Accuracy ±0.5 RDG (current/voltage) ??? Energy meter ???Instantaneous variables readout: 3 DGT ??? Energies readout: 7 DGT ???System variables: W, var, PF, Hz, Phase-sequence. ???Single phase variables: VLL, VLN, A, PF ??? Energy measurements: total kWh and kvarh ???TRMS measurements of distorted sine waves (voltages/currents) ???Self power supply ??? Dimensions: 4-DIN modules and 72x72mm ??? Protection degree (front): IP50 ???Application adaptable display and programming procedure (Easyprog function) ??? Easy connections management ??? Detachable display ??? Multi-use housing: for both DIN-rail and panel mounting applications

Approx. 10,500 / Piece Get Latest Price

Approx. 1,590 / Piece Get Latest Price