Power Analyzer

Approx. 5,680 / Number Get Latest Price

Product Brochure
Three-phase smart power analyzer with built-in advanced configuration system and LCD data displaying. Particularly recommended for the measurement of the main electrical variables. WM30 is based on a modular housing for panel mounting with IP65 (front) protection degree. Moreover, the analyzer can be provided with digital outputs that can be either for pulse proportional to the active and reactive energy being measured or/and for alarm outputs. The instrument can be equipped with the following modules: RS485/RS232, Ethernet, BACnet-IP or BACnet MS/TP communication ports, pulse and alarm outputs. Parameters programming and data reading can be easily performed by means of WM3040 Soft.

Features:

• One RS232 and RS485 port (on request)
• Communication protocol: MODBUS-RTU 
• MODBUS TCP/IP Ethernet port (on request)
• BACnet-IP over Ethernet port (on request)
• BACnet MS/TP over RS485, BTL approved (on request)
• Ethernet/IP port, ODVA approved (on request)
• Up to 2 digital outputs (pulse, alarm, remote control) (on request)
• Up to 4 freely configurable virtual alarms
• Up to 2 analogue outputs (+20mA, +10VDC) (on request)
• Class 0.5 (kWh) according to EN62053-22
• Class C (kWh) according to EN50470-3 
• Class 2 (kvarh) according to EN62053-23
• Accuracy ±0.2% RDG (current/voltage) 
• Instantaneous variables readout: 4x4 DGT
• Energies readout: 9+1 DGT
• System variables: VLL, VLN, A, VA, W, var, PF, Hz, Phase-sequence-asymmetry-loss.
• Single phase variables: VLL, VLN, AL, An (calculated), VA, W, var, PF
• Both system and single phase variables with average and max calculation
• Harmonic analysis (FFT) up to the 32nd harmonic (current and voltage)
• Energy measurements (imported/exported): total and partial kWh and kvarh
• Energy measurements according to ANSI C12.20 CA 0.5, ANSI C12.1 (revenue grade)
• Run hours counter (8+2 DGT)
• Real time clock function
• Application adaptable display and programming procedure (Easyprog function).

Approx. 60,000 / Piece Get Latest Price

Product Brochure
Three-phase power analyzer with built-in configuration keypad; Particularly indicated for the analysis of main, secondary and energy metering electrical variables. Housing for DIN-rail or wallmounting, IP40 (front) protection degree. Completely sealable housing. In case of direct connection up to 100A, the measuring input terminals are suitable for cables with a cross-section area from 6 to 35 mm2 . The special design of the instrument’s housing allows to add at any time the interface modules, even when the instrument is already installed.

The following modules are available:

• for all versions: pulses output; 
• only for the versions with auxiliary power supply: analogue output, RS485 port, alarm output or BUS Dupline.

Features:

• Front dimensions: 9 DIN modules 
• Analogue output by means of optional module (20mA or 10VDC)
• RS 422/485 Serial port by means of optional module
• Alarm output by means of optional module
• Dual pulse output by means of optional module
• Control of phase asymmetry
• Class 0.5 (current/voltage)
• Three-phase power analyzer
• Back-lighted LCD
• 4 x 31/2 DGT instantaneous variables read out
• 71/2 DGT energy read-out
• Measurements of system and phase variables: W, Wdmd, var, VA, VAdmd, PF (cos¿¿), V, A, Hz, THD-A, THD-V
• Measurements of total energies: kWh, kvarh
• Measurements of partial energies: kWh, kvarh
• Energy measurements according to EN61036 and EN61268
• TRMS measurements of distorted wave forms (voltages/currents)
• Two basic models: direct connection 20(100)AAC, CT 5(10)AAC and VT connection
• Maximum value indication of W dmd and VA dmd (only 5A version); maximum value indication of A (only 100A version).

Approx. 4,900 / Piece Get Latest Price

Carlo Gavazzi's energy management products provide information to identify consumption trends and take corrective actions. Real time power consumption monitoring also allows a site manager to anticipate overload conditions, exploiting alarm thresholds. Energy management equipment meets the requirements of commercial buildings, industry and production facilities, services and infrastructures. In addition, fiscal metering is possible in Europe thanks to MID certification

Approx. 80,000 / Piece Get Latest Price

Carlo Gavazzi Energy Management systems provide information so that operators can identify consumption trends and take corrective actions. Analysing the power profile operators can also aggregate loads and so negotiate more favorable terms with the utility company. Real-time power consumption monitoring also allows a site manager to anticipate overload conditions that would, for example, trip a circuit breaker. Alarm thresholds can be set to warn managers if preset limits are reached. Carlo Gavazzi Energy Management equipment meets the requirements of commercial buildings, Industry and production facilities, services and infrastructures.

Features:

• Wide range of power quality meters, energy meters, and transducers
• Fast installation, programming and display information reading
• Easy communications with PLC or PC control systems to provide plant-wide monitoring