New Items

Product Details:

3-phase compact power transducer. Particularly recommended for the measurement of the main electrical variables also on board of machines. Housing for DIN-rail mounting, with up to 3 analogue outputs, or RS485 communication port or alarm outputs or “Dupline” bus. Parameters programmable by means of UCS software.
• One digital output and RS485 communication port (2 wires only) • 16 freely configurable alarms with OR/AND logic linkable to up to 2 digital outputs • RS422/485/RS232 communication port (MODBUS-RTU), iFIX SCADA compatibility

Class 1 (kWh), Class 2 (kvarh) • Accuracy ±0.5 F.S. (current/voltage) • Compact power transducer • Instantaneous variables data format: 4 DGT • Energies data format: 8+1 DGT • System variables and phase measurements: VLL, VLN, A, Amax, An, Admd, Admd max, VA, VAdmd, VAdmd max, W, Wdmd, Wdmd max, WL1, WL2, WL3 max, var, PF, PFL1, PFL2, PFL3 min, Hz, ASY • Four quadrant power measurement • Energy measurements: total and partial kWh and kvarh (according to EN62053-21 and EN62053-23) • Hour counter (5+2 DGT) • TRMS meas. of distorted sine waves (voltages/currents) • Universal power supply: 90 to 260 VAC/DC, 18 to 60 VAC/DC • Dimensions: 45x83.5x98.5mm • Voltage asymmetry, phase sequence, phase loss control • Up to 3 analogue outputs (20mA or 10VDC) • 2 digital outputs

Product Details:

LDP loop detector is well suited to be used in parking, drive through and car access control applications to control barriers, gates, bollards and car access equipment. Automatic frequency tuning and easy sensitivity adjustment enable easy setup and installation. Automatic sensitivity boost ensures high bed vehicles are detected reliably. Multicolor LED indication enables user to easily adjust loop inductance and intuitively indicate installation issues for easy diagnostic. Individually user-assigned relay mode for 2 x SPDT outputs enables easy adaptation to many applications. Directional logic in dual loop model can be used to ascertain vehicle direction.Loop input inductance: 20 μH to 1000 μH • Adjustable sensitivity in 10 steps: 0.01% to 1.00% via potentiometer • Automatic loop frequency tuning or manual tuning via 4 adjustable loop frequency channels to avoid crosstalk • Automatic Sensitivity Boost (ASB) for high bed vehicle detection • Selectable fail safe and fail secure mode • 2 x SPDT relay outputs, selectable operation as pulse or presence switching • Multicolor power/fault LED indication for easy setup and intuitive diagnostic • Individual loop state multicolor LED to indicate different loop status and fault. • Loop diagnostic capability: loop short circuit, loop open circuit, inductance out of range, channel crosstalk. • Directional logic for dual loop. • Wide range power supply: 24-240 VAC/VDC, 45-65 Hz (LDPxPA2DU24) and 12-36 VAC/VDC, 45-65 Hz (LDPxPA2DU12).

Additional Information:

• Delivery Time: SAME DAY DELIVERY

Product Details:

The SMS20 and SMS31 safety modules are designed in Category 4, Performance Level e in accordance with the Machine Directive and EN ISO 13849-1 to monitor and control safely the safety circuits in applications with emergency stops, safety gates, safety magnetic switches, safety limit switches and electromechanical interlocks. They are also used to control safely the safety circuits of the lift car levelling, unintended car movement and the lift pit inspection, in compliance with the Lifts Standards EN 81-20 and EN 81-50.

Monitoring of safety circuits in applications with emergency stop buttons, emergency gates with electromechanical or non-contact safety switches, safety accesses with safety magnetic switches and interlocks • Monitoring of safety circuits with magnetic or electromechanical safety switches in Lifts to control the lift car levelling • Double or single safety channel operation • Control of up to 3 NO safety outputs with electromechanical safety relays • Selectable start/reset operating mode Manual, Automatic or Monitored Manual Start • Diagnostic of the safety circuit through on-board LED indications for power supply, status of safety channels and status of safety outputs • 1 NC auxiliary output (SMS31) that can be used for external status indication 

Product Details:

DWS-V-DBC05 is a cup anemometer designed for measuring air speed in a wide variety of applications, including wind turbines, buildings, cranes, weather stations, green-houses, etc. The product contains both PNP- and NPN open collector outputs, in which a fixed current is switched proportionally to the air speed at the rate of 10 pulses per m/s. The DWS-V-DBC05 is equipped with a specially designed protection mechanism, which protects the bearings and the electronic parts against dirt and humidity. The body of the sensor is made of black PVC, and the rotor is produced in stainless steel.

 Anemometer with opto-electronic detection
• Operating range: 1.5 to 75 m/s
• PNP and NPN open collector outputs in the same unit
• Current source outputs
• 10 to 28 VDC supply voltage
• All inputs and outputs are protected against reverse polarity and transients
• Dust sealing